大家在查： prearranged 鲁珀特百余位 SMEs 浩荡私宅脏东西 Shamanism excitation berthed

校核

na.check
网络verification; Checking; proofread

校核

英-汉网络释义

校核

check

水利工程专业英语 - 河林的日志 - 网易博客 ... chain of triangulation，三角锁 check，校核，对照 control point，控制点 ...

verification

校核（Verification）是确定模型和仿真准确地再现开发者的概念描述和技术要求的过程。验证（Validation）是确定模型和仿真 …

Checking

3 校核 (Checking) 23. 常规科学 27. 特许权使用费 24. 入学 28. 继承人 25. 新闻照片 29. 租船给游客 26. 慢车 30. 街道妇女练习...

proofread

校字的解释---在线新华字典 ... 校改〖 alteration;readandcorrectproofs〗校核〖 proofread〗校勘〖 collation〗 ...

collation

测量学专业词汇英语翻译（十七） ... 校对角 check angle 校核 collation 校检读定 calibrating ...

calibration

calibration的翻译中文意思... ... n.标定,定标,定分度 calibration n.校核,标定,率定 calibration 校准；定标 calibration ...

checked

变压... ... designating plate,illustration plate 标志牌，指示牌 designed,checked,approved 设计，校核，审定 destination 到站 ...

checking of

压力容器基本词汇 ... 现场安装 Field assembly 校核 checking of 泄放 Discharge ...

例句：

The equivalent heat transfer efficient is obtained from the calculation of the heat resistance , then check the wall thickness of heat pipe.

计算了热管热阻及等效传热系数，进行了热管壁厚强度的校核。

According to the torque value , calculating that of drill string downhole , and checking the safety of the drill string.

根据该扭矩值推算到井下钻柱的扭矩值，并且校核了各点钻柱的安全性。

Traditional design method is only to check up the structure . Its process is: hypothesis-analysis-checking up-re-design.

传统的结构设计实际是结构校核，其过程是假设一分析一校核一重新设计。

used for internal pressure vessel design and collation is provided , the way for the special uses and the range are also introduced .

绘制了内压容器设计与校核专用图，介绍了其使用方法及适用范围。

Study of The Key Components of the Up To Car Type "Rooftop Tent "

随车式 “车顶帐篷 ”关键部件的分析与校核

This article only some of the major components for the design and strength check of designed results are more reasonable .

本文只针对一些主要零部件进行设计和强度校核，设计出结果都是比较合理的。

On the basis denoted above, calibrating calculation is conducted on its stiffness , static strength , fatigue strength and its stability .

在此基础上，对支架进行了刚度、静强度、疲劳强度和稳定性校核计算。

According one parts of Switch mold parts to the requirements of the injection parameters of the machine was calibrated.

并根据开关一个零件注塑模具的要求对注射机的各参数进行了校核。

At last , the paper presents Wanzhou Bridge as the calculation example and checks the calculation method and program of this paper .

最后以万州二桥为算例，校核了本文的计算方法和程序。

The results show that all the verified temperatures are within the limit of those permitted by metal material .

结果表明，所有校核点的壁温均在管材所允许的范围之内。

After being verified through a number of experiment data , this method offers an extremely high accuracy .

该方法通过了大量试验数据的校核，具有较高的准确度。

Case study results show that using above-mentioned method the eigenvalue extraction and security check can be effectively realized.

算例结果表明，采用上述方法可以有效进行电网输电能力的特征提取和安全校核。

Finally, the stability, strength and stiffness of the optimized model was checked which testifies the reasonable of the light weight design .

优化后对车箱稳定性、强度和刚度再次进行校核，证明了轻量化设计的合理性。

A bottoms-up sample is commonly collected after a trip out of the hole or if an influx of formation fluid is suspected .

通常在起钻后或怀疑有地层流体流入井中的情况下采集校核井深泥浆样本。

With all the key structural parameters , the fuel flow can be validated according to the traditional experimental equation .

根据输油泵的关键结构参数，按照传统的经验公式进行了输油量的计算校核。

Structure, Clear the design ideas, stamping forming process and to each specific parts of the detailed calculation and test.

明确了设计思路，确定了冲压成型工艺过程并对各个具体部分进行了详细的计算和校核。

Finally , the inertial force of liquid was treated as a dynamic load and the strength of the container was calculated and checked .

最后，本论文将介质惯性力处理为动载荷，计算并校核罐式集装箱的强度。

Though an overall check of the allowable torques of various universal couplings , the corresponding safety coefficients are worked out .

对石油钻机现用万向联轴器的许用转矩进行了全面校核，揭示了其蕴含的转矩安全系数。

Since the mathematical model is based on the idealized one, errors are bound to exist .

由于传统强度校核公式是建立理想模型的基础上，存在近似误差。

校核

校核