大家在查：箱包配件发丝纹砂带机直丝粗粒度超细晶粒钢深过冷亚稳材料刻划硬度球型

拔模

网络Draft; Taper; Drafts

拔模

网络释义

拔模

Draft

热流道模具结构图模具设计 - 豆丁网 ... pmighttern 阵列； Draft 拔模、 offset 偏距、 ...

Taper

UG应用教程 - 读书网|DuShu.com ... 5. 5. 10 增厚薄体( Thicken Sheet) 5. 6. 1 拔模( Taper) 5. 6. 2 边倒圆( Edge Blend) ...

Drafts

...t) 3．3．2倒角(Chamfer) 3．3．3拔模(Drafts) 3．3．4抽壳(Shell) 3．3．5增减厚度(Thickness) 3．3．6螺纹(’rhread厂Tap) …

withdrawal

wrap中文 ... wire wrap 线圈 withdrawal 拔模 ... core wire straightening machine 芯骨校直机 ...

lifting of pattern

冶金词汇英语翻译(H-N) ... lift rope 卷扬绳 lifting of pattern 拔模 lifting pin 起模销 ...

Dran

...．4．1 分割线(SplitLines)2．4．2拔模(Dran)2．4．3 缩放比例(ScaleFeatures)2．5 分模工具(PartingTools)2．5．1 分型线(…

例句：

It all starts with a group of subject-matter experts creating draft guidance .

一切都需要从与一组主题专家创建拔模的指导。

The forging die has no draft angle and the material utilization rate is increased about 12 . 5%.

该模具结构使锻件的外形略去拔模斜度，材料利用率提高约 12 .

We suggest to enlarge the draft angle to help release the tool .

建议加大拔模角，以便脱模顺利。

Please draft the red surface along the core side to avoid sharp corner .

为避免模仁尖角，请修改红色面拔模至公模侧。

These results from the allowances made for thermal expansion effects and the need for draft angles on the forging tools.

这是由于为热膨胀效应而设置允差以及在锻模上需要拔模斜角所致。

This is facilitated by designing a draft , a slight angular offset from the vertical to the vertical surfaces of the pattern .

这可以通过设计一个拔模斜度，使它与模型的垂直面之间有一个小小的角度偏移量，便可容易地实现。

Please draft the red face along the cavity side .

请将红色面做公模侧拔模！

Please draft the green surface 3 degrees along the cavity side.

请将绿色面向母模侧拔模 3 度

Unless otherwise specified, All draft angles shall be 1 .

除非另有说明，所有拔模的角度应为 1 。

4 parting line edges, flash, gates, runner, and riser extensions to be 0 . 10 maximum .

分型面、飞边、浇口、浇道以及拔模斜度不超过 0 .

Please draft the red surface 2 . 0 degrees along the core .

请将周围红色面向公模侧拔模 2.0 度。

Enter a sweep distance of 0 . 9 mm and a draft angle of 4 degrees.

输入打扫距离 0.9 毫米和 4 度拔模斜度。

This can make complex shaped castings without any draft or flash.

它能制造没有拔模斜度和缝脊的复杂形状铸件。

the step of placing a drawing mould : the drawing mould matched with a drawing machine is placed in the main pipe;

放置拔模步骤：在主管内放置与拉拔机相配接拔模；

Boundary Representation Based Draft Operation and Its Application

基于边界表示的拔模算法及其应用

Study on the law of influence of drafting angle on upset-extruding

镦挤拔模斜度对成形的影响规律研究

Analysis in Cemented Carbide Drawing Die and Tribology Development

硬质合金拉拔模及摩擦学的发展分析

jolt squeeze stripper molding machine

震动压挤拔模造模机

拔模

拔模