大家在查：责任书 RehmanMalik bronchoplasty 复返陈必亭 south south 侯孝 formfitting 合不合幂幂

夹钳

na.clamp; tongs; grab; pliers
网络clip; clamp forceps; clamp frame

夹钳

英-汉网络释义

夹钳

clamp

考博词汇下载（10000词汇完整版） - 豆丁网 ... r v． n．吵闹，叫喊 clamp n．夹子，夹钳 clap v．拍，轻拍，拍手 ...

tongs

夹字的解释---在线新华字典 ... 夹起尾巴〖 tailbetweenhislegs〗夹钳〖 clinch;clamp;clip;tongs〗夹塞儿〖 jumpthequeue〗 ...

clip

夹字的解释---在线新华字典 ... 夹起尾巴〖 tailbetweenhislegs〗夹钳〖 clinch;clamp;clip;tongs〗夹塞儿〖 jumpthequeue〗 ...

clamp forceps

数控剪板机前送料机-青岛阿玛达数控机械有限公司 ... 送料精度 Feed accuracy 夹钳 Clamp Forceps 机器重量 Machine weight ...

clamp frame

进出口专业英语词汇(C4) ... clamp drill 夹钻 clamp frame 夹钳 clamp gate valve 滑门阀 ...

cramp

通讯专业词汇库 - MBA智库文档 ... cramming 补充/填满 cramp 夹钳 crane 起重机 ...

gripper

冶金(Metallurgy)专业词汇(D-H) - 不锈钢世界 ... grinding wheel 研磨砂轮 gripper 夹钳 gripping 咬入 ...

例句：

The summary of the full text and the view of microassembly robot and micro gripper researches have been shown in the end of dissertation .

论文结尾对全文做了总结，并对微装配机器人技术、微夹钳技术、信息反馈等进行了展望。

Install 6' crossbars between the front and rear clamps on both sides .

在两侧，在前夹钳和后夹钳之间安装 6 英尺的横（十字）杆。

The required length of BOPP film is brought down by grippers; the bunch is wrapped and pushed to the sealing station .

BOPP 薄膜的所需长度击落的夹钳，挑的包装和密封被推到车站。

Use them to turn meat on a ridged grill pan , to toss salads , mix pasta with sauce and rotate cake and pie tins in the oven .

使用夹钳翻转烤架上的食物，搅拌沙拉，使意大利面充分沾有肉酱，将烤箱里的蛋糕和苹果派翻面。

2-Pull the edge joint tight with clamps . Make sure that both boards are aligned correctly, so that the surface is flat .

图 2 。用夹钳加紧对接的木板，确保两块木板对齐，这样才能保证拼出来的是一个平面。

Remove the buttons on the front clamps only .

仅仅卸去前夹钳上的按钮。

Remove the wedges on the 6 ' (1 . 83 m ) anchoring side bars between the front and rear clamps and remove the bars.

卸去前后夹钳之间 6 英尺（1.83 米）支承侧杆上的隔离楔，并卸去这些侧杆。

You should not apply tremendous force with your clamps because this will drive too much glue from the joint .

不应该把夹钳的力量调的太大，因为那样会挤出过多的胶水。

Another unique feature of the MPG5 is the dual-purpose purge port that is part of every gripper .

另一个 MPG5 特点是双用途清洗端口，每个夹钳的一部分。

c. Stainless steel pipe cutting machine , band saw , GF saw, clamp etc. such material should be the same as the pipe or the same category .

不锈钢管割管器、带锯、GF 锯，夹钳等这些材质应与管道材料相同或同一类别。

The clamps shape need as that of crucible , Avoiding the concertrate stress destruction the crucible .

坩埚夹钳应与坩埚形状相符，避免局部受力损坏。

the experiments indicate that the gripper can work reliably and safely , and can satisfy the needs of microassembly tasks .

实验证明该微夹钳工作可靠，能够满足微装配机器人装配任务的要求。

Remove the front clamp jaw from the pinchweld clamp .

从焊接压板夹钳上卸去前夹钳卡爪

As shown , the rotary manifold and gripper is a clean compact assembly which allows the gripper to rotate freely without rotating air lines.

如图所示，旋转夹持器是多方面的，清洁的小型集会，允许夹钳旋转线可以不旋转的空气。

These bars should drop in easily between the clamp body and the anchoring side bar retainer button on the clamp flange.

这些侧杆应该很容易在夹钳体和夹钳法兰上的支承侧杆之间的保（夹）持按钮之间下降。

Feed clamp device make positioning correct and clamping reliable , ensure the workprece parallelism and precision of the shearing size.

送料夹钳定位准确，夹紧可靠，能精确地保证板料的剪切精度。

The clamp frame of probe can be clasp on many pipes to measuring temperature of outside surfaces .

夹钳形探头能夹住各种管道，适用测量各种管道外表温度。

Transport the finished clamps to the next step .

将加工完成的夹钳运到下一个工序。

Tighten the clamps slowly to allow any excess glue to escape and leave the joint clamped until the glue sets.

要慢慢紧固夹钳，以便多余的胶水能被挤出来，在胶水固化前一直保持夹持状态。

Remove the wedges from the bottom of the swivel clamps and the 6'4 " anchoring crossbar . "

从可旋转夹钳和 6 英尺 4 英寸的支承横（十字）杆的底部卸下隔离楔。

Pliers and nippers . Multilingual nomenclature .

夹钳和虎钳 .多种语言名称表

夹钳

夹钳