大家在查： FitchRatings justice ministry Soil quality 奥瑞特•范•希尔登辨清九点汤克斯 small intestines 敌对状态努力推

进给

na.【机】feed
网络Feed; feeding; FEEDS

进给

英-汉网络释义

进给

Feed

CA6250B 卧式车床_行业中国车床供应商 ... 主轴 Spindle 进给 Feed 进给数量 No. of feeds ...

feeding

汽车配件英语速查 - 外贸英语 -... ... feed back control 反馈控制 feeding 供给，进给 fender board (车身)挡泥板 ...

FEEDS

宇杰CK6140数控车床 ... TURRET 刀架 FEEDS 进给 JAILSTOCK 尾座 ...

Feed rate

力劲MV-1680立式加工中心-中国机床网 ... 工作台（ Table) 进给（ Feed rate) 刀库（ A.T.C) ...

Feedrates

PROE... ... Upr mode Prep code establishing inv Time mode 时间代码 Feedrates 进给 Disable feed override 禁止进给重写 ...

infeed

轧机英语词汇 - 豆丁网 ... shaft 轴 infeed 进给 operating 操纵、控制 ...

feed in

feed to gain ratio_翻译 ... 饵料： feed 进给： feed in 饲料： Animal Feed ...

例句：

Reduce rapid traverse and federate, and always be ready to shut down the machine immediately if necessary.

检查加工程序，应使用较小的快速移动速度和进给速度，必要时，时刻准备立即关闭机床

The thermal medium is fed so that the front edge of the thermal medium moves a second distance from the edge detection sensor .

热敏介质进给使得热敏介质的前边缘移动距离边缘检测传感器第二距离。

The static and dynamic properties of the CNC drilling machine feeding system is one of the main factors that affect the precision .

数控钻床进给系统静、动特性是影响加工精度的主要因素之一。

The feeding speed must be changed with continuousness and a rule, which can let the lathe work well .

旋切过程中刀刃进给速度必须按一定规律变化才能保证旋切机正常工作。

Result shows that the controller can achieve the requirements of the ultra-precision machining in the case of uncertainties existed .

结果显示，在被控对象存存不确定因素的情况下，采用陔控制器能够使伺服进给系统满足超精密加工的要求。

Up milling (conventional milling). In up milling the workpiece is fed against the direction of cutter rotation , as shown in Fig . 12. 3a.

逆铣（传统铣削）：在逆铣中，工件逆着铣刀转动的方向进给，如图 12.3a 所示。

For the same size of billet and finished shape , the total effective strain of ring increases with increasing feed speed.

同样尺寸的坯料和成品，芯辊进给速度越大，内层的累积等效变形越大；

Through the numerically controlled unit head, the transverse feed amount and feed speed of a cutting tool are accurately controlled .

本发明使刀具的横向进给量和进给速度得到了精确控制。

Sawing machines with fixed tool during operation , having a fixed bed with manual feed of the work piece or with a demountable power feed .

工作时，圆锯片不移动，有固定床身，采用手工送料进给或可拆卸动力送料的圆锯机。

Rough turning tools can be right-hand or left-hand types, depending upon the direction of feed .

粗车刀具按其进给方向可以是右手型的或是左手型的。

Application They are used for the main feed mechanism of shearing gate on CNC-Controlled paper cutting machines .

用于数控切纸机裁切门主进给机构。

With the hydraulic control system its cutting speed can be adjusted randomly by the size and the thickness of the caliber .

它采用液压进给，进给量切削速度可根据口径大小、臂厚随意调整。

The plunge-cut method, in which grinding is achieved through the cross feed of the grinding wheel and no axial feed is applied .

插入 -切削方法：这种方法通过砂轮的横向进给完成磨削而不采用轴向进给。

After mechanical transmission , the change of rotating speed of the motor can be transformed into range in the variation scope of speed .

经过机械传动后，电动机转速的变化范围即可转化为进给速度的变化范围。

As far as the direction of cutter rotation and workpiece feed are concerned, milling is performed by either of the following two methods .

至于涉及到铣刀转动的方向和工件的进给，铣削可以通过下列两种方法之一进行。

Hardness, flatness and surface roughness of the roll barrel can be ensured by controlling the speed and cutting feed amount.

通过控制速度与进给量来保证辊身硬度、平直度及表面粗糙度要求。

The results showed that: the depth of cut had the main influence on cutting force followed by feed rate and cutting speed in turn .

研究结果表明：切削用量中背吃刀量对主切削力的影响最大，进给量次之，切削速度对主切削力的影响最小。

The research indicates that the parameters of the speed loop are beneficial for avoiding the self-sustaining pressure oscillate . . .

研究表明速度环参数对消除进给系统的自激振荡有积极作用。

Feed and dressing movements are controled by means of two independent driving systems.

机床的进给及修正，由二个互不干涉的传动机构执行。

Emphatically researched on tool cutting process, a blunt cutting edge and feed rate of the processing quality is analyzed .

分析圆弧刃刀具切入过程、切削刃钝圆和进给量对加工质量的影响。

进给

进给