大家在查： movie theater 数亿计嫌太文恩杨朱 infer blacked 王力约翰·格雷 passenger flow

过盈

n.interference
网络crush; Yav

过盈

英-汉网络释义

过盈

interference

工程图纸英语 - 豆丁网 ... 间隙配合 clearance fit 过盈 interference 过盈配合 interference fit ...

crush

轮机英语核心词汇总结 - 豆丁网 ... nip 过盈间隙 crush 过盈 be subjected to 遭受… ...

Yav

平均过盈（Yav）为最大过盈与最小过盈的平均值。平均过盈： Yav= 1 2 (Ymax+Ymin) （2-9） 6．过渡配合

1

Bearings with a tapered bore are always mounted with an interference fit .

带圆锥孔轴承始终以过盈配合安装。

2

For bearings having a tapered bore , inner rings are always mounted with an interference fit .

对于圆锥孔轴承，内圈的安装始终采用过盈配合。

3

This reduction can be measured to determine the degree of interference and the proper fit .

通过测量减小值，可以判定过盈度以及配合的松紧程度。

4

The performance of automotive water pump bearing seal is closely related with the magnitude of interference of the sealing lip .

汽车水泵轴承密封圈的密封性能与唇口过盈量密切相关。

7

The values for the probable interference or clearance cover 99 % of all the combinations of the theoretical interference or clearance.

可能的过盈配合或游隙配合数值包括 99%的全部理论过盈配合或游隙配合组合。

8

Multiring press fit is one effective way of solving the problem that the radial strength of composite flywheel is too low .

采用多环过盈装配是解决复合材料飞轮径向强度过低的有效途径之一。

10

Bearings with clearance fits are usually easier to mount or dismount than those with interference fits.

游隙配合的轴承通常比过盈配合的轴承容易安装或拆卸。

11

12

interference connection is formed between the mortice and the false tongue .

所述槽和榫舌构成过盈连接。

13

This paper deals with designed theory and method for interference fit between plastic shaft and plastic hub .

陈述了塑料实芯轴与孔座间过盈连接的设计理论和方法。

14

The planet gear shafts and the axis holes of the planet gears are connected under an interference fit .

行星齿轮轴与行星齿轮的轴孔之间为过盈配合。

15

In this article, a valuable advice of renovating rotatory shaft of giant machine was introduced .

介绍了一种大型机器转轴修复的有效方法 ———双重过盈法。

17

By changing the size of interference values, the optimal range has been determined .

通过改变过盈量大小，确定最优过盈量范围。

18

Aerospace series . Pins, shear, headed, close tolerance .

航天系列 .带头和过盈公差的光轴

20

The fretting wear between matching parts became severe with increasing of load and speed .

随着载荷和速度的提高，汽车链过盈配合表面的微动磨损加剧。

21

22

Alignment needle roller bearings should have an interference fit in the housing bore .

对中滚针轴承的轴承座孔应过盈配合。

23

24

In this paper the authors analyse the hydraulic bulging roller after shrunk-fitting using the method of elasticity for the first time .

首次通过弹性力学的计算，对液压胀形轧辊过盈配合时的情况进行了分析。

25

Pigging and caliper with clear pig diameter than pipe diameter usually to interference by 5% to 8%.

清管和测径用的清管器直径通常比管道内径要过盈 5%至 8%。

26

Stress and force finite element analysis of Cylinder sleeve assembly process of interference based on ABAQUS has been done .

基于 ABAQUS 软件对圆柱套筒过盈装配过程的应力分布、接触力进行了有限元仿真。

27

The interference fits of bushing bearing has been calculated by finite element method based on ANSYS .

以 ANSYS 为平台，对衬套与轴承座的过盈联接进行了有限元计算。

28

Clear help clear the pig diameter than pipe diameter usually to interference by 5% to 8%.

清管用的清管器直径通常比管道内径要过盈 5%至 8%。

29

To prevent this , interference fits must be used .

要防止这一点，必须使用过盈配合。

30

热词推荐

大家在看