大家在查：信号采集多圈编码器圈数提升设备旋转编码器屏蔽线轴型集电极开路输出类型绝对值编码器

超差

na.overproof
网络out of tolerance; SLOPPY; oversize

超差

英-汉网络释义

超差

out of tolerance

摘要: 超差(out of tolerance) 产品外形尺寸超出了产品标准规定的公差范围。是金属塑性加工产品的一种质量缺陷。

SLOPPY

铁姆肯|铁姆肯轴承|北京奥通昌盛... ... SKIP LOT SAMPLING: 跳跃式的产品抽样：对 SLOPPY: 超差：公差的极限值，通常在 …

overproof

在线英语词典,英文翻译,科技词典,专业词典,... ... 144 瞄准点： aiming-point 145 超差： overproof 146 单目标： single-objectiv…

oversize

请教机加工中专业词汇的对应英文词（组）_百度知道 ... 31.参数： parameters 32.超差： oversize 33.合格品： quality product ...

os

翻译_秋名山_新浪博客 ... ORNAMENT 装饰物 OS 超差 OUTBOARD 外侧的 ...

Castle in spain

食物味道平平，服务态度超差(Castle in spain)脆脆乳猪件(RABIT) 晚餐算正常, 服务要改善(C and A) 点心质素不错(samurai) 下 …

beyond poor

当地警方根据校区内安装的摄像镜头进行调查侦破，以期锁定嫌犯。结果发现，摄像镜头里的影象过于模糊，质量超差（beyon…

TURBOLEG.

...闭弹簧呢?因为在下的排气阀门早已失去作用,骑乘感觉超差(TURBOLEG....),如知晓请不吝告之.....谢谢!!

例句：

Through the appropriate adjustment of process parameters and the production practical tests the distortion and out-of-tolerance are solved .

适当调整工艺参数，经生产实践验证，解决了变形超差问题。

In case that nonlinear error exceeds permissible limit, adaptive linearization control strategy was adopted to smooth the tool orientation .

针对可能出现的超差情况，采用基于矢量平滑的自适应误差控制策略对误差进行补偿。

Installment logistics management (1), strengthening logistics management, logistics process to prevent the ultra-poor into pieces .

物流批次管理（1 ）、加强物流管理，防止物流过程中混入超差件。

The results afford theoretical base for gauge control at head and tail ends and were proved by practice .

这些分析为今后钢板头尾厚度超差的控制方法提供一定的理论依据。

SLOPPY : Extreme limits of tolerance , usually outside .

超差：公差的极限值，通常在外径上发生。

There was something living under the floor boards in our room and the staff were discraceful.

我们房间地板下好像住着什么不知名的东东一样，还有服务态度超差超没仪态。

Have many kinds of alarms that overtime , exceed difference, vibration to output .

具有超时、超差、震动等多种报警输出。

Denotes the need to correct defective radii on product such as nicked , torn, or undersized radii.

指需要修复产品上有缺陷的倒角，例如划痕，磨损或超差的倒角。

Analysis and Countermeasures for the Cause of the Over-Difference of Vibration in Turning Plant

运转设备振动超差主要原因分析及对策

The quenching crack and dimension super-error of lantern ring made of T8 steel appear after double liquid quenching ;

T8 钢制套圈经双液淬火易出现淬裂和尺寸超差；

The Computer Aided Diagnostics of Pitch Error Out of True Primary in Lathe -turning Helical Burr

车削螺纹中螺距误差超差原因的计算机辅助诊断

Analysis of the width off-tolerance of hot rolled narrow strip and its resolution methods

热轧窄带宽度超差原因分析及对策

Testing Contrast of Cement Strength by the ISO Method and Analysis on the Cause of Ultra Difference

ISO 法水泥强度检验对比情况及超差原因分析

Deviation correction of engineering piles for mechanic static pile loading and their preventive measures in common use

机械静压法沉桩工程桩偏超差及常用预防措施

Superficially analyse the reasons caused the error of the remote sensing precipitation meter

浅析遥测雨量计超差原因

Analysis of Causes to Side Bearing Clearance Being Over the Tolerance and the Preventative Measures

旁承间隙超差的原因分析及防止措施

The Determinant and Replacement of the Indication Errors of Ground Temperature Sensor

地温传感器示值超差的判定与更换

Fast nickel brush electroplating for renovation of rotor journal on dimensional tolerance

快速电刷镀镍工艺修复转子轴颈尺寸超差

Cause and counter measure of gear common normal length exceeding tolerance in slotting machine process gear

插制齿轮时公法线长度变动超差的原因探析及对策

Research and Analysis on the Cause of Errors of Parallel ism for Milling Semi - circle Key Slot

铣半圆键槽平行度超差原因分析与研究

Study of the flatness deviation of side wall for box car

棚车侧表面平面度超差问题研究

The Error Reason of Electrometer in the Calibration Period to Analyze and Countermeasure

电能表检定周期内超差原因分析与对策

Technique Dealing about Transnormal Error of Thermohydrosensor

温湿度传感器气温误差超差的技术处理

The control of unevenness on the partial base plate of a large pot

大型槽罐底板局部凹凸超差的控制

Dealing with Over Tolerance of Characteristic Value of Tested Reducing Valve

减压阀试验特性值的超差处理

Approach to roundness over-tolerance in machining of thin wall workpieces

薄壁类零件加工中圆度误差超差问题探讨

超差

超差