大家在查：中心差赤道装置黄道坐标系统上海基康生物技术有限公司长波授时台基本圈诏命百马图西园雅集图袁安碑

环规

n.ring gauge; ringer gage
网络ring gage; calibration ring; setting rings

环规

英-汉网络释义

环规

ring gauge

机械专业英语词汇（很全） - Lemon Tree ... radius 半径 ring gauge 环规 sine bar 正弦量规 ...

ring gage

机械词汇的英语翻译--打印文章 ... ring bolt 环首螺栓 ring gage 环规 ring gear 环形齿轮 ...

calibration ring

航海及海运专业词汇英语翻译(C2) ... calibration range 标定范围 calibration ring 环规 calibration screw 校准螺钉 ...

setting rings

关于三丰_测量技术_职场_西祠胡同 ... 14 dial bore gages （粗糙表面）内径表 15 setting rings 环规 16 dial depth gages 深度 …

Inspection of Tools

龙燡企业有限公司 ... Insert Pin 插入针 Inspection of Tools 环规 Tungsten Thimble 钨钢顶针 ...

gauge ring

滚动轴承技术词汇 - G ... ... gauge pressure 表压力，计算压力 gauge ring 环规 gear 齿轮，传动装置 ...

external cylindrical gauge

gauge-英汉词典... ... external calliper gauge 外卡规 external cylindrical gauge 环规 external limit gauge 极限量规 ...

例句：

Thread ring gauge is the tool for an all-around checking about the male threads which with the female threads.

螺纹环规是一个对外螺纹进行全面综合检查的一个工具。

The fit should be approximately the same on both sides of the ring to insure proper straightness .

配合度应两面基本相同，以确保环规的直线度。

Turn the adjusting screw clockwise , which opens the ring to a larger pitch diameter than the setting plug .

顺时针调节螺钉，这使环规开口，并使中径比校对塞规的大。

Turn the adjusting screw counter-clockwise until there is a slight drag between the ring and setting plug.

反向旋转调节螺钉，直到塞环规间有轻轻的拉动

Length measuring instruments . Plain ring standard grauges.

长度测量仪表 .普通标准环规

Clean and inspect ring gages for nicks and embedded metal filings and burrs .

清洗检查环规的划痕和陷入的金属铁销、毛刺。

Spot welding equipment . Taper plug gauges and taper ring gauges .

点焊设备 .阳锥形塞规范和阴锥形环规

That includes aligning the ring gauge before measuring for dia .

那包括在测量直径之前排校准环规。

Confirm all pitch diameters and class size match the ring gages.

确认所有的中经和等级都与环规匹配

Turn the ring gage locking screw counter-clockwise until it is loosened .

与逆时针方向旋转环规上的紧固螺钉直到他们松开。

STEEL GAUGES . METRIC TAPER RING GAUGES WITH TANG.

钢制规 .榫式 5%锥度环规

STEEL GAUGES . MORSE TAPER RING GAUGES WITH TANG.

钢制规 .榫式莫氏锥环规

STEEL GAUGES . METRIC TAPER RING GAUGES .

钢制规 .螺丝孔 5%锥度环规

Remove the ring from the setting plug and repeat operations 10 and 11 on the other side of the ring gage.

移下环规，调面，重复步骤 #10 和 #11

STEEL GAUGES . MORSE TAPER RING GAUGES .

钢制规 .螺丝孔莫氏锥环规

The measuring equipment for ring gauge which is composed of SIP550 and standard ring gauge is given.

利用标准环规和高准确度测长机来建立环规检定的标准装置。

GO ring gauges and setting ring gauges from 1 mm up to 315 mm nominal diameter for use in precision engineering

精密机械用的公称直径 1 至 315mm 的过端环规和调节环

Verification of geometrical parameters - NOT GO ring gauges - Part 1: Nominal diameter from 1 mm up to 315 mm; general purpose

几何尺寸检验 .不过端环规 .第1 部分：公称直径 1-315mm .一般用途

Estimation on Measurement Indetermination of Second -Class Gauge Standard Device

二等环规标准装置测量不确定度估算

d - type fuse - bases d iii 63 a up to 660 v , for back connection , with flange , for gauge rings

环规用 d63a660v 以下背面接线带凸缘的 d 型熔断器

General-purpose GO screwring gauges for ISO metric screw threads from 1 mm up to 200 mm nominal diameter

一般用途的螺纹公称直径 1 至 200mm 的 ISO 米制螺纹过端环规

Collection of Environment Parameter in First Grade Ring Gauge Standard Device

一等环规标准装置中环境参数的采集

Qualified Plain Internal Diameters for Use as Master Rings and Ring Gages, Measurement of

用作校准环规和环规的合格普通内径的测量

Measurement of qualified plain internal diameters for use as master rings and ring gages

用作校对环规和环规合格普通内径的测量

Spot Welding Equipment - Taper Plug Gauges and Taper Ring Gauges Second Edition

点焊设备。锥度塞规和锥度环规，第

Calibration Procedures for Thread Ring Gages

螺纹环规校正方法

Metric taper gauges; taper ring gauges for taper shanks with drift tang

米制锥度量规 .带扁尾锥柄用锥度环规

Respiratory protective devices and diving apparatus - Standard thread - Part 2: GO ring gauges and NOT GO ring gauges

呼吸保护器 .潜水器 .圆螺纹 .第2 部分：螺纹过端环规和螺纹不过端环规

环规

环规