大家在查：树脂自硬砂造型机床铸件发泡模具李纯一展厅设计模具工艺吊包通用工艺装备锻造裂纹钢辊

加工余量

n.allowance for finish
网络machining allowance; Admittance; process redundancy

加工余量

英-汉网络释义

加工余量

machining allowance

电梯专业英语词汇（三） ... machining 机械加工 machining allowance 加工余量 machining in general 普通机械加工 ...

Admittance

饭桶精英 ... Admission cam shaft 进气凸轮轴 Admittance 导纳；加工余量；通道 Advanced ignition 提前点火 ...

process redundancy

石油词汇英语翻译(P) ... process pipeline 工艺管线 process redundancy 加工余量 process scanning 过程扫描 ...

finish allowance

模具行业中英翻译对照表-1 - 豆丁网 ... 参考图 REFERENCE DRAWING （12） 加工余量 FINISH ALLOWANCE 抛光度 FINIS…

working allowance

机械英语词汇|各类常用英语词汇 ... work 工件 working allowance 加工余量 working dischard 加工废料锻铸造关连用语 ...

finishing allowance

机械英语词汇|各类常用英语词汇 ... endless grinding belt 循环式研磨带 finishing allowance 加工余量 grain 磨粒 ...

allowance for finish

自制专业英语字典_百度文库 ... alleviate 减轻 allowance for finish 加工余量 altitude 海拔高度 ...

例句：

This technology is employed predominantly for workpieces with relatively large allowances (up to 5 mm).

所以此种工艺主要用于带有相对较大加工余量（至 5mm ）的工件。

I produced the luminous Baoyu stone blocks , with Jiagongyuliang small, the materials used in, the less waste characteristics .

我公司生产的夜光宝玉石料块，具有加工余量小，用料省，废料少的特点。

The paper discusses in detail the principle of selecting the stock of turbine blade and determining the allowance for machining the stock.

详细论述了汽轮机叶片各种毛坯形式的选择原则及毛坯机械加工余量的确定。

The complex surface matching and machining allowance solving have been done.

叶片曲面的匹配及加工余量的计算。

Jiagongyuliang products are small , sophisticated organizations , fatigue -resistant, long-lived, non-polluting, high efficiency and so on.

产品具有加工余量小，组织精密，耐疲劳，寿命长，无污染，高效益等特点。

Rough castings of cast iron with spheroidal graphite - General tolerances, machining allowances; inactive for new design

球墨铸铁毛坯 .一般公差及加工余量 .不适于新结构

Heavy metal alloy raw castings; pressure die castings; general tolerances, machining allowances

重金属合金的铸件毛坯 .压铸 .一般公差及加工余量

Light metal alloy raw castings; pressure die castings; general tolerances, machining allowances

轻金属合金的铸件毛坯 .压铸 .一般公差及加工余量

Rough castings of heavy metal alloys ; gravity die castings, general tolerances, machining allowances

重金属合金的铸件毛坯 .金属模铸造 .一般公差及加工余量

Light metal alloy raw castings; gravity die castings; general tolerances, machining allowances

轻金属合金的铸件毛坯 .金属模铸造 .一般公差及加工余量

Steel Forgings; Machining Allowances and Permissible Variations for Seamless Open-die Forged Bushes

钢锻件 .自由锻造的套筒的加工余量及允许偏差

Rough steel castings - General tolerances, machining allowances; inactive for new design

铸钢毛坯 .一般公差及加工余量 .不适于新结构

Steel raw castings of malleable iron - General tolerances, machining allowances; inactive for new design

可锻铸铁毛坯 .一般公差及加工余量 .不适于新结构

Die forgings of aluminium and aluminium alloy--Dimensional tolerance and machining allowance

铝及铝合金模锻件的尺寸偏差及加工余量

Steel Forgings; Machining Allowances and Permissible Variations for Open-die Forged Pierced Discs

钢锻件 .自由锻造的带孔圆盘的加工余量及允许偏差

Rough castings; general tolerances and machining allowances; general

铸件毛坯 .一般公差及加工余量 .总则

Machining allowances and tolerances for steel open die forgings on hammer --Forging without machining

锤上钢质自由锻件机械加工余量与公差黑皮锻件

Rough castings of grey iron - General tolerances, machining allowances; inactive for new design

片状石墨铸铁毛坯 .一般公差及加工余量 .不适于新结构

Analysis of Allowance and Dimensional Determination of Investment Casting

熔模铸件加工余量分析及铸件尺寸的确定

Steel Forgings; Machining Allowances and Permissible Variations for Open-die Forged Discs

钢锻件 .自由锻造的圆盘的加工余量及允许偏差

Machining allowances and tolerances for steel open dle forgings on hammer--Single throw crankshaft

锤上钢质自由锻件机械加工余量与公差单拐曲轴类

Steel Forgings; Machining Allowances and Permissible Variations for Open-die Forged Bars

钢锻件 .自由锻造的棒件的加工余量及允许偏差

straight - sided spline machining allowance and tolerances

矩形花键 .加工余量及公差

Machining allowances and tolerances for steel open die forgings on hammer--Shaft without steps

锤上钢质自由锻件机械加工余量与公差光轴类

Machining allowances and tolerances for steel open die forgings on hammer--Disks and columns

锤上钢质自由锻件机械加工余量与公差盘、柱类

Research on the Rapid Determining Method for Roughcast Allowance and Tolerance

铸件机械加工余量及尺寸公差快速确定方法的研究

Machining allowances and tolerances for steel open die forgings on hammer--Disk swith holes

锤上钢质自由锻件机械加工余量与公差带孔圆盘类

加工余量

加工余量

machining allowance

Admittance

process redundancy

finish allowance

working allowance

finishing allowance

allowance for finish

热词推荐

大家在看