大家在查： 'scall Requeststobeverified Ahn Tartt 灵山县 692亿 Unbewohnt 无限富足 1140年伊巴丹

轴类

网络shaft; Pin, Shaft; Shafts

轴类

网络释义

轴类

shaft

●心轴类(shaft)、管件(pipe fitting)、铸件(mold)、模具(die) ... 等2.扣件(Fastener)：●螺纹类：螺丝(screw)、螺帽 (nut)、螺栓(bo…

Pin, Shaft

轴类(Pin, Shaft)杯士(Bushes) 齿轮(Gears) 工程塑胶类制品: 杯士(Bushes) 齿轮(Gears) 生产制造: 机械制造: 2. 手摇塑胶吹气机

Shafts

GermanQualitySourcing ... Precise steel profile parts 精密钢型材 Shafts 轴类 Heavy sheet metal parts 重钣金件 ...

Axis

　　轴类(Axis)：组合X轴和Y轴，其中Y轴有多个(除去第一个)。应考虑以下几种情况：　　1. 显示外框　　2. 显示网格(必显示外框) 　　3. X轴 …

sympodial

（2）复轴类（sympodial）：　　　主轴的生长通常只维持到一年后再由新生侧芽所取代，而每个新芽皆会从老茎的部位长出，并且 …

rubber parts

采购商- 广东进出口商会 ... 组件 Magnetic （齿轮,轴类,管类） rubber parts 铝管连接器 Al ...

例句：

Alloy coating is prepared by induction melting and casting with the method of direct feeding powder on the surface of a shaft .

采用直接送粉方式在轴类零件表面感应熔铸合金层，简要介绍了工艺原理、工装特点。

The results obtained in this study could be used for a hollow part deformation by the similar process .

研究结果对楔横轧工艺在轧制空心阶梯轴类件的应用具有指导意义。

In remanufacturing , additional value of the used shaft components can be fully extracted and residual value is dig out to the most extent .

再制造能充分提取报废轴类零件中的附加值，最大限度地挖掘废旧轴中的剩余价值。

After a shaft component fails , mostly it is directly discarded and replaced with a new one, which results in a huge waste .

轴类零件失效后，往往直接报废而更换新品，造成了极大的浪费。

Main failure modes of shaft components of construction machinery and their remanufacturing processes are briefly described in the article.

着重介绍了工程机械轴类零件的主要失效形式及再制造方法。

The factory is the production of large machine screw , light bars, bars and switching products sentinel longer shaft production enterprises .

本厂是生产大型机床丝杠、光杠、开关杠及加长轴类产品的定点生产企业。

相似零件特别是轴类零件具有相同或相似的特征信息。

On cutting principle aspects, it resolves the key problem that cutting speed low in the turning miniature spindles .

它从切削原理上解决了微细轴类零件车削加工时切削速度低的问题。

Wear is the main failure mode of shaft components in construction machinery .

磨损是工程机械轴类零件失效的主要形式。

CNC lathe is mainly used for machining shaft, disk type and so on rotational parts .

数控车床主要用于加工轴类、盘类等回转体零件。

For the sake of the axis accessory's figuration , the experiment of second wedge heavy section shrinkage was carried out.

为了成形大断面收缩率轴类零件，进行了楔横轧二次楔入试验。

Abrasion of shafts widely exists in the production of industry and agriculture .

轴类部件的损坏是工农业生产中常遇到的问题。

It provides a reference for selecting method of repairing abraded shafts .

这为磨损轴类零件的修复方法的选用提供了借鉴意义。

The theoretical model of measuring shaft forging is analyzed .

分析了测量轴类锻件的理论模型。

A fuzzy neural network model based on entropy clustering is applied to analyze shaft parts .

针对轴类零件，应用熵聚类模糊神经网络聚类技术进行分析。

Founded in 1993 , is a specialized production enterprise car shaft .

成立于 1993年，是专业化的汽车轴类产品生产企业。

Choice of form tolerance of bearings parts .

轴类零件形位公差的选用。

Spraying of dryer of papermaking and axle .

造纸烘缸、轴类的喷涂。

Design of Automatic Checkout Equipment Used for Axle Part

轴类零件的自动检测装置设计

Blanking roll forging process design and shakedown of a complicated curved long-axis forgings

一种复杂弯曲长轴类件制坯辊锻工艺设计与调试

An Experimental Study of Laser Cladding Technology Applied for Axle Surface Repair

激光熔覆技术应用于轴类零件表面修复的实验研究

轴类

轴类